Lamotte SMART3 Colorimeter User Manual Page 149
- Page / 294
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
PROCEDURE
Use COD/UDV adapter.
1. Homogenize sample if necessary.
2. Preheat COD heater block to 150±2°C.
3. Remove cap from COD tube. Hold tube at a 45° angle. Use a graduated pipet,
to carefully add 0.2 mL sample water allowing the sample to run down the side
of the tube.
4. Cap and mix thoroughly.
5. Rinse the outside of the tube with distilled water. Wipe dry with a paper towel.
6. Repeat steps 3 through 5 using 0.2 mL distilled water. This is the reagent blank.
7. Place tubes in preheated COD block heater and maintain temperature at
150±2°C for two hours.
8. At the end of the heating period turn the heater off. Wait 20 minutes for the
tubes to cool to 120°C or less.
9. Remove tubes from block heater. Invert several times to mix.
10. Allow to cool to room temperature.
11. Press and hold
until colorimeter turns on.
12. Press
ENTER
to select TESTING MENU.
13. Select ALL TESTS (or another sequence containing 026 COD HR) from
TESTING MENU menu.
14. Wipe the blank tube with a damp towel to remove fi ngerprints and smudges.
Wipe with a dry towel.
15. Scroll to and select 026 COD HR from menu.
16. Insert reagent blank tube into chamber. Select SCAN BLANK.
17. Remove tube from colorimeter.
18. Insert digested water sample tube into chamber. Select SCAN SAMPLE.
Record result. For the most accurate results, take three readings on each
sample and average the results.
19. Press to turn colorimeter off or press
EXIT
to exit to a previous menu or
make another menu selection.
NOTES: Reagents are light sensitive. Unused reagents should be stored in the
shipping container, and in the refrigerator if possible, until needed.
A reagent blank should be run with each set of samples and with each lot of
reagents.
The reacted blank will be stable if stored in the dark.
To eliminate error caused by contamination, wash all glassware with 20% sulfuric
SMART3 Test Procedures 11.10 COD, High Range
Test Procedures
- CONTENTS 3
- GENERAL INFORMATION 5
- LIMITS OF LIABILITY 6
- WARRANTY 6
- REGISTER YOUR METER 6
- SPECIFICATIONS 7
- 6 SMART3 Colorimeter 11.10 8
- CONTENTS AND ACCESSORIES 9
- ACCESSORIES 9
- EPA COMPLIANCE 10
- CE COMPLIANCE 10
- IP67 CERTIFICATION 10
- CHEMICAL TESTING 11
- Sampling of Closed System 12
- FILTRATION 12
- SMART3 Colorimeter 11.10 11 13
- REAGENT BLANK 14
- METER CARE 14
- CALIBRATION 15
- CALIBRATION CURVES 15
- 14 SMART3 Colorimeter 11.10 16
- SMART3 Colorimeter 11.10 15 17
- STANDARD ADDITIONS 18
- MEASUREMENTS 19
- INTERFERENCES 20
- STRAY LIGHT INTERFERENCE 20
- OPERATION OF THE 21
- SMART3 COLORIMETER 21
- COMPONENTS 22
- GENERAL OPERATING PROCEDURES 23
- 22 SMART3 Colorimeter 11.10 24
- Result or 25
- LOOPING MENUS 26
- TESTING MENU 27
- TEST SEQUENCES 28
- GENERAL TESTING PROCEDURES 28
- 1.00 ppm 30
- SMART3 Colorimeter 11.10 29 31
- 0.28 ppm 32
- 0.30 ppm 33
- 32 SMART3 Colorimeter 11.10 34
- SMART3 Colorimeter 11.10 35 37
- EDITING MENU 38
- SMART3 Colorimeter 11.10 37 39
- Editing/Set Up 39
- ADDING OR DELETING A TEST 40
- ADDING A TEST 40
- DELETING A TEST 42
- SMART3 Colorimeter 11.10 41 43
- EDIT USER TESTS 44
- U V W X 46
- H I J K 46
- S T U V 47
- 2 3 4 5 47
- E P Q R 47
- O P Q R 47
- 46 SMART3 Colorimeter 11.10 48
- 0 1 2 3 50
- 1 1 2 3 50
- . – 0 1 51
- SMART3 Colorimeter 11.10 51 53
- 52 SMART3 Colorimeter 11.10 54
- – 1 2 3 55
- O 1 2 3 55
- . – 0 1 55
- SETTING THE CLOCK 59
- LOGGING DATA 60
- FACTORY SETUP 61
- SETTING POWER SAVE 61
- 60 SMART3 Colorimeter 11.10 62
- SETTING THE BACKLIGHT TIME 63
- SELECTING A LANGUAGE 64
- SMART3 Colorimeter 11.10 63 65
- COMPUTER CONNECTION 66
- BATTERY/AC OPERATION 67
- MAINTENANCE 68
- TROUBLESHOOTING 69
- TROUBLESHOOTING GUIDE 70
- 1910-TEST 71
- 02.13.12 71
- REAGENT SYSTEMS 73
- ALKALINITY–UDV 77
- ALUMINUM 79
- AMMONIA NITROGEN - LOW RANGE 81
- PROCEDURE - FRESH WATER 82
- PROCEDURE - SALT WATER 82
- AMMONIA NITROGEN - HIGH RANGE 84
- BENZOTRIAZOLE/TOLYLTRIAZOLE 89
- BENZOTRIAZOLE PROCEDURE 91
- TOLYLTRIAZOLE PROCEDURE 92
- BIGUANIDE 93
- BORATE - UDV 95
- PROCEDURE 100
- Test Procedures 101
- PROCEDURE A: 102
- BROMINE (NO CHLORINE) 102
- PROCEDURE B: 102
- PROCEDURE C: 103
- BROMINE - UDV 105
- PAN METHOD • CODE 4017-01 109
- CHLORIDE 111
- CHLORINE 113
- PROCEDURE–FREE CHLORINE 115
- PROCEDURE–TOTAL CHLORINE 115
- PROCEDURE–COMBINED CHLORINE 119
- CHLORINE, FREE - UDV 121
- CHLORINE, TOTAL - UDV 125
- CHLORINE DIOXIDE 129
- CHROMIUM, HEXAVALENT 131
- CHROMIUM - HEXAVALENT 133
- TRIVALENT & TOTAL 133
- HEXAVALENT CHROMIUM PROCEDURE 135
- TRIVALENT CHROMIUM PROCEDURE 136
- PAN METHOD · CODE 4851 137
- COD – LOW RANGE 139
- COD – STANDARD RANGE 143
- COD – HIGH RANGE 147
- PLATINUM COBALT METHOD 151
- NO REAGENTS REQUIRED 151
- COPPER – LOW RANGE 153
- CUPRIZONE METHOD • CODE 4023 155
- COPPER – UDV 159
- CODE 3660-01-SC 163
- CYANURIC ACID 167
- CYANURIC ACID – UDV 169
- DISSOLVED OXYGEN 173
- FLUORIDE 177
- HARDNESS, TOTAL – UDV 181
- HYDRAZINE 183
- HYDROGEN PEROXIDE – LOW RANGE 185
- DPD METHOD • CODE 4045-01 187
- HYDROGEN PEROXIDE – SHOCK 189
- IRON – UDV 195
- PAR METHOD · CODE 4031 201
- MANGANESE – LOW RANGE 203
- MANGANESE – HIGH RANGE 205
- TMK METHOD · CODE 4861 207
- PREPARATION OF *TMK INDICATOR 208
- MOLYBDENUM – HIGH RANGE 209
- NITRATE - UDV 215
- NITRATE-NITROGEN – LOW RANGE 219
- NITRITE-NITROGEN – LOW RANGE 223
- NITROGEN, TOTAL 225
- OXYGEN SCAVENGERS 229
- DEHA PROCEDURE 231
- CARBOHYDRAZIDE PROCEDURE 232
- ERYTHORBIC ACID PROCEDURE 233
- HYDROQUINONE PROCEDURE 234
- METHYLETHYLKETOXIME PROCEDURE 235
- DPD METHOD • CODE 4881 237
- PROCEDURE - OZONE ONLY 238
- INDIGO METHOD • CODE 3651-SC 241
- PROCEDURE–LOW RANGE 242
- PROCEDURE–HIGH RANGE 243
- PHOSPHATE – LOW RANGE 251
- PHOSPHATE – HIGH RANGE 255
- PHOSPHATE ppb 257
- PHOSPHORUS, TOTAL - LOW RANGE 261
- DIGESTION • CODE 4025-01 265
- POTASSIUM 269
- SILICA – LOW RANGE 271
- SILICA – HIGH RANGE 275
- SULFATE – HIGH RANGE 277
- SULFIDE – LOW RANGE 279
- SURFACTANTS 283
- CODE 3666-01-SC 285
- TURBIDITY 287
- ZINC – LOW RANGE 289
- APPENDIX 292
- Appendix 293
Related products and manuals for Equipment Lamotte SMART3 Colorimeter
Equipment Lamotte SMARTLink3 User Manual
(8 pages)
(8 pages)
Equipment Lamotte SMART 2 User Manual
(258 pages)
(258 pages)
Equipment Lamotte TDS 5 Meter User Manual
(12 pages)
(12 pages)
Equipment Lamotte 3590-03 User Manual
(8 pages)
(8 pages)
Equipment Lamotte STH Outfit User Manual
(24 pages)
(24 pages)
Equipment Lamotte AR-42 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 2.213 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals